1 Cartridge (50 ml) LB Wash (Fast Set) 1 Cartridge (50 ml) RB Wash (Fast Set) 3 Cartridges (50 ml) Tray (Fast Set) 1 Cartridge (50 ml) Bite Registration 1 Extruder 6 Small Mix tips 6 Intraoral Syringe Tips (Small Universal) 6 Large Mix tips
Danville Start VPS Alpha Bite 50 ml Cartridge 2 pack Start VPS™ incorporates a series of vinyl polysiloxane (VPS) impression and bite registration materials intended to allow dentists to take accurate impressions of all types of tooth structures for various purposes, such as crown and bridge, implantology, etc. Start VPS materials are odorless, tasteless (except for Vanilla Flavored Stiff Bite), and immersible in disinfectants. They offer dimensional stability, tear resistance, and accuracy of impression. Total time for material to set: 4:30 minutes
Danville Start VPS Alpha Bite Econo 50 ml Cartridge 24 pack Start VPS™ incorporates a series of vinyl polysiloxane (VPS) impression and bite registration materials intended to allow dentists to take accurate impressions of all types of tooth structures for various purposes, such as crown and bridge, implantology, etc. Start VPS materials are odorless, tasteless (except for Vanilla Flavored Stiff Bite), and immersible in disinfectants. They offer dimensional stability, tear resistance, and accuracy of impression. Total time for material to set: 4:30 minutes
FEATURES: Excellent recovery after deformation Good hydrophilicity High-contrast shades Tailored to all dental requirements KEY SPECIFICATIONS : TECHNICAL DATA: Silagum Comfort Silagum Varnish Application time* 1.45mins 2mins Setting time in mouth 6 min Setting (curing) time* 15 min 15 min Evaporation time Disinfection of the Automix-Dispenser The Automix-Dispenser and the trimmer and brush holders can be reused after disinfection and sterilization, but should be replaced if there are visible signs of wear (e.g. scratches). The device can be disinfected and sterilized using a commercially available immersion disinfection solution. DMG recommends using only RKI (Robert Koch Institute) listed disinfection solutions. The Automix-Dispenser is also autoclavable Storage and Shelf Life Store in a dry space at normal room temperature (15 – 25 °C / 59 – 77 °F) Do not store in the refrigerator or freezer Keep out of direct sunlight Leave used mixing tips on the cartridge after use. They serve as a cap Do not use past the expiration date DIRECTIONS TO USE : Direct relining in the patient’s mouth 1. If necessary, remove old permanently soft relining material. 2. Trim off a minimum of 1 mm of all the areas needing to be relined. DMG recommends a rounded preparation of the edges of the dentures. Note: Following this preparation, protect the denture surface from moisture, saliva, and monomer-containing resins. 3. Apply an even layer of primer (Silagum-Comfort Primer) in accordance with the manufacturer’s information and let the solvent evaporate completely (approx. 1 minute). Be sure to completely cover the ridges and edge areas. Apply at least two coats 4. Apply Silagum-Comfort first on the ridges and edges of the denture and then on the base of the denture. The layers should be at least 2 mm thick 5. Remove saliva with a suction instrument. Caution! Uncured silicone can trigger the patient’s gag reflex. Therefore, to prevent the silicone from entering the patient’s throat and esophagus, be sure that the patient is sitting upright and slightly bent forward when performing any functional movements. 6. Insert the denture into the patient’s mouth within the specified application time and instruct the patient to bite into normal occlusion. Have the patient perform gentle swallowing and chewing movements (without exerting excessive pressure) for 5 minutes with his or her mouth closed 7. Remove the denture from the mouth after approximately 6 minutes and let it harden 8. Clean and disinfect the denture. Note: If needed, carefully align the dry and grease-free relining by applying and modeling additional Silagum-Comfort. Let it set in the patient’s mouth for 7 minutes or in a pressure pot (40 – 50 °C) for 5 minutes 9. Remove excess material with sharp scissors or a scalpel. Smooth the trimmed edges with a suitable silicone trimmer 10. Using a brush, apply the Silagum-Comfort Varnish to the treated areas in accordance with the manufacturer’s instructions, avoiding air bubbles as much as possible, and then let dry. Indirect relining at the laboratory 1. Following a functional impression, the gypsum is poured into the denture on the jaw side and mounted on a relining jig. Note: Do not use polyether as the impression material. The impression material used should have a long application time and appropriate viscosity. DMG recommends applying a suitable separating medium (gypsum against resin) 2. Produce a negative by pouring the occlusal part of the denture or rows of teeth, which must be firmly fixed in its vertical relationship to the model. For this purpose, DMG recommends using a special relining device that facilitates the exact repositioning of model and negative (cuvette) 3. Remove impression material 4. Trim the denture surface on the jaw side at least 1 mm and clean it. Note: Following this preparation, protect the denture surface from moisture and monomer-containing resins 5. Apply an even layer of primer (Silagum-Comfort Primer) in accordance with the manufacturer’s information and let the solvent evaporate completely (approx. 1 minute). Be sure to completely cover the ridges and edge areas. Apply at least two coats 6. Apply Silagum-Comfort first on the ridges and edges of the denture and then on the base of the denture. The layers should be at least 2 mm thick 7. Reposition the denture on the model, and use the cuvette to completely envelop the negative 8. Let the material set and harden for 10 minutes in the pressure pot at 40 – 50 °C. Note: If needed, carefully align the dry and grease-free relining by applying and modeling additional Silagum-Comfort. Let it set in the pressure pot for 5 minutes (40 – 50 °C) 9. Remove excess material with sharp scissors or a scalpel. Smooth the trimmed edges with a suitable silicone trimmer 10. Using a brush, apply the Silagum-Comfort Varnish to the treated areas in accordance with the manufacturer’s instructions, avoiding air bubbles as much as possible, and then let dry. Packaging DMG Silagum Comfort Varnish: 2 x 10 ml Bottle (Base & Catalyst)
Ideal balance of clinical properties. Excellent hydrophilicity to help you get void-free impressions*. Memory: Elastic recovery resists distortion for a more accurate impression*. Toughness: Resists tearing.
Impregum Penta Polyether impression material helps get an accurate impression on the first take--reducing the need for costly adjustments, remakes and retakes. Get accurate detail even in moist conditions with this polyether impression material. Excellent flow property best captures fine details for precise impressions. Indications: Used in crown, bridge, inlay or onlay, functional, implant, denture and partial denture impressions. • Regular setting time
Brand : Impregum Impression Type : Final Material : Polyether Viscosity : Medium Set Type : Regular Set
Suggested Applications Crown and bridge impressions. Inlay and onlay impressions. Functional impressions. Implant abutments. Clear aligner impressions. Study model impressions. Quick-setting materials especially suited for single-unit and two-unit impressions. Removable denture and partial denture impressions. Impression Type Final Material VPS Physical Strength Higher, Medium Product Type Material Setting Time Regular Set Viscosity Heavy Body
Indications : Crown and bridge impressions Inlay and onlay impressions Functional impressions Implant impressions
Delivery System : Pentamix Mixing Unit Impression Type : Final Material : VPS Physical Strength : Higher Product Type :Material Setting Time : Regular Set Trademark : Penta Viscosity : Heavy Body
Imprint 4 VPS material offers you: Active self-warming For accelerated setting Shortest intra-oral setting time* For real time savings and patient comfort Sufficient working time For a stress-free procedure Super-hydrophilicity For excellent flow and the finest detail reproduction Fresh material colours For enhanced readability Pleasant minty taste For more patient comfort
